Ignore:
Timestamp:
Mar 1, 2019 12:56:34 PM (4 years ago)
Author:
srkline
Message:

verification of the updated beam centers based on fitted arcs of Silver Behenate

File:
1 edited

Legend:

Unmodified
Added
Removed
  • sans/Dev/trunk/NCNR_User_Procedures/Reduction/VSANS/V_Marquee_Operations.ipf

    r1119 r1131  
    365365                 
    366366// if measured on the LEFT panel, convert to the RIGHT coordinates for the reference value       
    367 // these corrections are exactly the opposite of what is done in V_fDeriveBeamCenters(xFR,yFR,xMR,yMR) 
     367// these corrections are exactly the opposite (subtract, not add) of what is done in V_fDeriveBeamCenters(xFR,yFR,xMR,yMR) 
    368368                if(cmpstr(detStr,"FL") == 0) 
    369 //                      Print "FRONT Reference X-center (cm) (Velocity Selector) = ",x_mm/10 + (0.03 + 0.03)/2   // OLD pre Dec 2018 
    370 //                      Print "FRONT Reference Y-center (cm) (Velocity Selector) = ",y_mm/10 - (0.34 + 0.32)/2 
    371                         Print "FRONT Reference X-center (cm) (Velocity Selector) = ",x_mm/10 - 0.13     // NEW Dec 2018 values 
    372                         Print "FRONT Reference Y-center (cm) (Velocity Selector) = ",y_mm/10 - 0.35 
    373                                                  
    374         //              Print "FRONT Reference X-center (cm) (Graphite) = ",x_mm/10 + 0.03 
    375         //              Print "FRONT Reference Y-center (cm) (Graphite) = ",y_mm/10 - 0.28 
     369                        Print "FRONT Reference X-center (cm) (Velocity Selector) = ",x_mm/10 - kBCtrOffset_FL_x         // NEW Dec 2018 values 
     370                        Print "FRONT Reference Y-center (cm) (Velocity Selector) = ",y_mm/10 - kBCtrOffset_FL_y 
    376371                endif 
    377372                 
    378373                if(cmpstr(detStr,"ML") == 0) 
    379 //                      Print "MIDDLE Reference X-center (cm) (Velocity Selector) = ",x_mm/10 + (0.06 + 0.05)/2 
    380 //                      Print "MIDDLE Reference Y-center (cm) (Velocity Selector) = ",y_mm/10 - (0.14 + 0.01)/2 
    381                         Print "MIDDLE Reference X-center (cm) (Velocity Selector) = ",x_mm/10 - 0.26 
    382                         Print "MIDDLE Reference Y-center (cm) (Velocity Selector) = ",y_mm/10 + 0.16 
    383                                          
    384         //              Print "MIDDLE Reference X-center (cm) (Graphite) = ",x_mm/10 + (0.06 + 0.05)/2 
    385         //              Print "MIDDLE Reference Y-center (cm) (Graphite) = ",y_mm/10 - (0.14 + 0.01)/2 
     374                        Print "MIDDLE Reference X-center (cm) (Velocity Selector) = ",x_mm/10 - kBCtrOffset_ML_x 
     375                        Print "MIDDLE Reference Y-center (cm) (Velocity Selector) = ",y_mm/10 - kBCtrOffset_ML_y 
    386376                endif 
    387377        endif 
Note: See TracChangeset for help on using the changeset viewer.